| {{ 'ml-lesson-number-slides' | message : article.intro.bblockCount }} |
| {{ 'ml-lesson-number-exercises' | message : article.intro.exerciseCount }} |
| {{ 'ml-lesson-time-estimation' | message }} |
Here are a few recommended readings before getting started with this lesson.
At Jefferson High, a local volunteer group wants to construct a wheelchair ramp located at the school's entrance. LaShay is helping with the project and she is given a model of the ramp. It is represented on a coordinate plane.
The slope of the ramp must be less than 0.2 for a person on a wheelchair to be able to use it comfortably. Help LaShay determine the slope, and then tell the ramp makers if the plan is acceptable
or not acceptable.
In order to understand the relationship between two quantities and make predictions about their behavior, it is important to be able to compare and quantify how one changes with respect to the other. These ideas define the concept of rate of change.
The rate of change ROC is a ratio used to compare how a variable changes in relation to another variable. It is determined by dividing the change in the output variable y by the change in the input variable x. For any ordered pairs (x1,y1) and (x2,y2), the rate of change is calculated using the following formula.
The Greek letter Δ (Delta) is commonly used to represent a difference. This leads to an alternative way of writing the formula for ROC.
Rate of Change=ΔxΔy
The units of a rate of change are the ratio of output units to the input units, meaning that they are derived units. Interpreting the rate of change depends on the context.
Output Units | Input Units | Rate of Change Units | Possible Interpretation |
---|---|---|---|
meters | seconds | secondmeters | Car speed over a certain period of time |
bacteria | hours | hourbacteria | Growth rate of bacteria in an experiment |
U.S. dollars | hours | hourU.S. dollars | Worker's hourly wage |
LaShay, a student who volunteers often, is really into learning how to build accessible places for people of all abilities. She is now downloading a package of design files created by professional designers. It explains how to make such places.
The school library's internet speed allows her to download 5 megabytes (MB) of data each minute. This is shown in the following table.
The amount of data downloaded after 5 minutes is 25 MB.
Finally, try to draw a line passing through these points.
As shown, all of the points lie on the line. This makes sense because the rate of change is constant.
The rate of change of a linear relation, which is constant, has a special name — slope.
The slope of a line passing through the points (x1,y1) and (x2,y2) is the ratio of the vertical change — the change in y-values — to the horizontal change — the change in x-values — between the points. The variable m is most commonly used to represent the slope, and the variable k is also used.
m=change in x-valuechange in y-value
The phrase rise over run
is commonly used to describe the slope of a line, especially when the line is given graphically. Rise
refers to change in y-value and run
refers to change in x-value. The right triangle used to visualize the rise and run between two points on the graph of a line is called slope triangle.
The definition of the slope of a line can be written in terms of its rise over its run.
m=runrise
The sign of each distance matches the direction of the movement between the points. The run is positive if the direction moves right. Whereas, the run is negative if the direction moves left. Similarly, moving upward results in a positive rise, while moving downward results in a negative rise.
There are different ways to determine the slope of a line. Which method to use depends on how the relation is expressed.
To begin, mark any two points on the line. It is helpful to mark points with integer coordinates. This helps with accuracy.
From here, it is necessary to determine the rise and run between the points. Note that this can be done in either order.
Draw a line from A to the x-coordinate of point B to determine the horizontal distance between the points. Then, count the number of steps the line segment spans. Recall that moving to the right results in a positive run, while moving to the left results in a negative run.
In this graph, the run spans 4 units and it is positive.
The rise between points can be found in the same way. Remember, moving up results in a positive rise and moving down results in a negative rise.
The rise spans 2 units and it is also positive.
After downloading the design files, LaShay found a quiet spot in the library to dive into all the cool ideas. She feels inspired after seeing the design of this great accessible park. LaShay realizes that reading through all of these great designs could take quite some time. She already read through quite a few pages. The following graph shows the number of pages left to read and the time she figures it will take.
Find and interpret the slope of this relation.Mark any two points on the line. Then, calculate the rise and run between them.
Begin by identifying any two points on the line. This is to find the slope of the relation. Notice that the line passes through the points (3,9) and (7,3).
Next, determine the rise and run between the two points.
Now that the rise and run are both known, the slope ratio can be calculated.rise=-6, run=4
Put minus sign in front of fraction
Calculate quotient
Find the slope of the given line by determining the rise and run. Write the answers in decimal form.
LaShay wants to not only learn about making accessible features in public spaces, she wants to donate money to groups that do. She saves the money she will donate by depositing the same amount in her piggy bank daily.
She wants to know how much money is in the bank before breaking the cute little figure. She assumes the piggy bank had $12.50 after five days and $17.50 after seven days.
Now that there are two points on the plane, draw a line passing through them to obtain the line of the relation.
This graph matches the one given in option A. Therefore, graph A represents the relation.
Substitute (5,12.5) & (7,17.5)
Subtract terms
Calculate quotient
Substitute (5,12.5) & (x,30)
Subtract terms
LHS⋅(x−5)=RHS⋅(x−5)
Distribute 2.5
LHS+12.5=RHS+12.5
LHS/2.5=RHS/2.5
Find the slope of a line passing through the given points using the slope formula.
Throughout this lesson, the concept of rate of change and its relation to the concept of slope have been examined. The challenge presented at the beginning of the lesson can now be solved. Recall that at Jefferson High, a wheelchair ramp is being made for the front entrance. LaShay got a hold of the ramp's design displayed on a coordinate plane.
The slope of the ramp must be less than 0.2. LaShay wants to find the slope of the ramp to decide whether the current design is acceptable or not.Choose two points on the same side of the ramp. Then use the slope formula to find the slope of the ramp.
Begin by choosing two points on the the same side of the ramp. Choosing points that lie directly on the lattice of the graph helps make the required calculations easier.
Next, substitute these points into the slope formula to find the slope of the ramp.Substitute (-5,-1) & (5,2)
-(-a)=a
Add terms
Calculate quotient